Ditapis dengan
ISO 683-14 Heat-Treatable Steels and Free-Cutting Steels Port 14: Hot-Rolled …
ISO 683-14:2004 gives the technical delivery requirements for round and flat bars and wire rods manufactured from alloyed steels intended for hot-formed and subsequently heat-treated springs or cold-formed and subsequently heat-treated springs.
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 683-14: 1992 (E)
- No. Panggil
- 621.3673 ISO H
Metalica Materials-Tensile Testing at Elevated Temperature
-
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 783-1989 (E)
- No. Panggil
- 621.3673 ISO M
Heat-Treatable Steels, Alloys Steels and Free-Cutting Steels. Port 13: Wrough…
-
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 683/13 - 1986 (E)
- No. Panggil
- 621.3673 ISO H
Metalic Materials-Bend Test
Specifies the method for determining the ability of metallic materials to undergo plastic deformation in bending. Applies to the bend test of test pieces taken from metallic products as specified in the relevant product standards. It is not applicable to certain materials and/or products, for example tubes in full section or welded joints, for which other standards exist.
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 7438-1985 (E)
- No. Panggil
- 669.00212 ISO M
Metalic Materials-Hardness Test-Rockwell Test (Scales A-B-C-D-E-F-G-H-K)
-
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 6508-1986 (E)
- No. Panggil
- 669.00212 ISO M
Recommended Protice For Radiographie Examination of Fusion Welded Joints - Pa…
The detection of flaws in an item submitted to X- or gamma-radiographic examination depends on the particularities of the technique employed. This part of ISO 1106 specifies general techniques of weld radiography with the object of enabling satisfactory results to be obtained economically. The techniques are based on generally accepted practice and the fundamental theory of the subject.
- Edisi
- Part 3
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 1106/3-1985 (E)
- No. Panggil
- 621.3673 ISO R
Recommended Protice for Radiographe Examination of Fusion Welded Joints - Por…
Specifies general techniques of weld radiography with the object of enabling satisfactory results to be obtained economically. The techniques are based on generally accepted practice and the fundamental theory of the subject. Does not lay down radiographic criteria of acceptance for the joints, but is concerned with the radiographic techniques to be used.
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 1106/2-1985 (E)
- No. Panggil
- -
Natural Gas-Determination of Hydrogen, Inert Gases and Hydrocarbons up to C8-…
This International Standard describes a precise and accurate method for the analysis of natural gas. The gas sample shall not contain any hydrocarbon condensate and/or water. The method requires the use of two columns which can be put into one or two gas chromatographs. The constituents of the eluent of the first column are detected by a thermal conduc-2 References
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 6974-1984 (E)
- No. Panggil
- 544.92 ISO N
Nuclear Power Plants-Main-Tainability-Terminology
Identifies the typical parameters and terms necessary for collecting and exchanging maintainability data. The definitions are valid for corrective maintenance. For preventive maintenance, a similar classification can be drawn up. The general guidelines on the exchange of reliability data for nuclear power plants are given in ISO 6527.
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 8170-1993 (E/F)
- No. Panggil
- 621.48 ISO N
Structural Steels-Plates, Wide Falts, Bars, Sections and Profiles
Applies to steel plates with thicknesses of 3 mm and over, wide strips in coils with widths greater than or equal to 600 mm, and greater than 6 mm in thickness, wide flats, bars and hot-rolled sections generally used in the as-delivered condition and normally intended for bolted, riveted structures.
- Edisi
- -
- ISBN/ISSN
- -
- Deskripsi Fisik
- -
- Judul Seri
- ISO 630 : 1995 (E)
- No. Panggil
- 671.80218 ISO S
Karya Umum 
Filsafat 
Agama 
Ilmu-ilmu Sosial 
Bahasa 
Ilmu-ilmu Murni 
Ilmu-ilmu Terapan 
Kesenian, Hiburan, dan Olahraga 
Kesusastraan 
Geografi dan Sejarah